Pond Skimmer & BioFalls Installation: Sealing, Placement, FAQ Skip to content
Skimmer and BioFalls Installation: Placement, Faceplate Sealing, and What Each One Actually Does

Skimmer and BioFalls Installation: Placement, Faceplate Sealing, and What Each One Actually Does

Published: November 2026  |  Read time: 14 min  |  By: Pond Pro Direct Team  |  Level: DIY Intermediate. Every price on this page is our live listed price; figures we have not yet confirmed in the field carry a red VERIFY badge.

Quick Answer

A pond skimmer and a BioFalls (waterfall filter) are the two halves of an ecosystem pond's filtration: the skimmer sits at the pond edge, pulls debris off the surface, and houses your pump; the BioFalls sits at the top of your waterfall and hosts the bacteria that keep the water safe for fish. If your kit includes both, you do not need to buy another filter for a normally stocked pond.

The two steps that decide whether your pond leaks are sealing the skimmer faceplate and attaching the liner to the BioFalls. Both use the same method: fish-safe 100% silicone, liner sandwiched flat against the housing, screws snugged by hand, and a full cure before water touches the seal. Get those two seals right and the rest of the install is digging and plumbing.

What Each Component Actually Does

Most first-time builders treat the skimmer and the falls filter as two mystery boxes in the kit. They are not interchangeable, and neither one works properly without the other. Here is the division of labor:

Skimmer BioFalls / Waterfall Filter
Where it sits Buried at the pond edge, opening at the waterline Buried at the top of the waterfall, above pond level
Job Mechanical pre-filtration: pulls leaves, pollen, and floating debris into a basket or net before they sink and rot Biological filtration: beneficial bacteria colonize the media and convert toxic ammonia into harmless nitrate
What's inside Debris basket or net, filter mat, and your pump Filter mats plus bio media (lava rock or plastic media in mesh bags)
Protects Your pump, from clogging on debris Your fish, from ammonia and nitrite
Water flow Water in through the faceplate opening, out through the pump Water in through a bulkhead at the base, up through the media, over the spillway lip
Maintenance Empty basket weekly in season, rinse mat monthly Rinse media a few times per year, in pond water only

The pump lives inside the skimmer, which is the detail that makes the whole system work: every gallon gets debris stripped out before it reaches the pump and the biological media, so neither clogs. That is also why skimmer placement matters more than any other decision in the install.

Which Models We Carry (Live Pricing)

These are our current listed prices, pulled from the store today, not a spec sheet:

Component Rated For Price
Aquascape Signature Series 1000 BioFalls Ponds up to 1,000 gallons $415.99
Aquascape Signature Series 2500 BioFalls Ponds up to 2,500 gallons $773.99
Aquascape Signature Series 6000 BioFalls, 2" bulkhead Ponds up to 6,000 gallons $1,259.99
Aquascape Signature Series 6000 BioFalls, 3" bulkhead Ponds up to 6,000 gallons, high-flow plumbing $1,349.99
EasyPro PSA7000 Axiom Pro-Series Skimmer Large koi and ecosystem ponds $440.99

Sizing rule: match the falls filter to your pond volume, then go one size up if you keep koi. An oversized biological filter has no downside except price; an undersized one means water quality battles every summer. If you are not sure of your volume, run the math in our pond sizing guide first.

Which Setup Do You Need? Decision Branches

Building a new pond from scratch

Buy a complete kit, not components. Every kit we carry pairs a skimmer and falls filter that are matched to each other and to the included pump, which removes the single most common component-buying mistake: a pump that overdrives the skimmer or starves the falls. Kits with skimmer and falls filter run $1,170.89 to $5,743.99 depending on pond size.

Adding or upgrading filtration on an existing pond

Size the falls filter to your actual volume from the table above, and plan the retrofit for spring or fall when you can drop the water level. Retrofitting a skimmer into an existing liner is doable but it means cutting your liner and setting the faceplate height exactly at your established waterline, so read the faceplate section below twice before committing.

Building a pondless waterfall

You do not need a skimmer at all. Pondless systems use a buried pump vault and reservoir instead, because there is no open water surface to collect debris. Start from our waterfalls and fountains collection instead of this page.

Dedicated koi pond with a bottom drain

A skimmer still helps with surface debris, but the primary filtration architecture is different: bottom drain to settlement chamber to bead or drum filter. The BioFalls becomes a supplemental polishing stage rather than the main biological filter. If this is your build, talk to us before buying; this page covers ecosystem-style ponds.

When NOT to Buy a Skimmer

  • Container ponds and very small water gardens under roughly 500 gallons. A skimmer box is physically oversized for the job; a small all-in-one pump and filter plus a weekly pass with a hand net does the same work for a fraction of the cost.
  • Pondless waterfalls. As above: no surface, no skimmer.
  • Wildlife-first ponds. Skimmers occasionally pull in frogs and small wildlife along with the leaves. A dedicated wildlife pond is usually better served with a planted shallow zone, more plant coverage, and manual netting. If you run a skimmer anyway, check the basket daily in spring, not weekly.
  • "My pond is under trees, a skimmer will solve it." It will not. A skimmer handles normal debris load. A pond directly under heavy deciduous canopy needs fall netting no matter what filtration you install, and we would rather tell you that before you spend the money.

Installing the Skimmer: Placement and the Faceplate Seal

Here is the uncomfortable truth that the kit brochures soft-pedal: your skimmer faceplate opening sets your pond's water level, permanently. Water will never sit higher than the point where it can flow into the skimmer. Set the skimmer an inch too low and your finished pond runs an inch lower than your coping was designed for, with exposed liner to show for it. This is the one measurement in the whole build to obsess over.

Placement

  1. Pick the edge opposite your waterfall. Water should travel the full length of the pond from falls to skimmer so circulation covers the whole surface, with no dead corners where debris collects.
  2. Excavate a shelf on undisturbed soil. The skimmer must sit on soil that has never been dug, or on mechanically compacted base material. A skimmer set on loose backfill settles over the first season, and when it settles, your faceplate seal tears or your water level drops.
  3. Set the height off your finished waterline, not the ground. Use your level line from excavation. Follow your model's template: on typical designs the waterline sits about an inch below the top of the faceplate opening, so the weir floats correctly. Check the template that ships in the box, not a rule of thumb, because opening geometry differs by brand.
  4. Level the skimmer in both directions and backfill around it in compacted lifts once the seal has cured and the pond is filling.

Sealing the Faceplate Without Leaks

Nearly every skimmer leak traces back to one of four errors at the faceplate: silicone in the wrong place, liner stretched instead of relaxed, screws overtightened, or water let in before the cure finished. The sequence that avoids all four:

  1. Dry-fit first. Drape the liner over the skimmer face with generous slack and make sure the liner lies flat against the skimmer wall with no stretched or bridged sections. Relaxed liner seals; stretched liner pulls away over time.
  2. Do not cut the opening yet. The liner gets cut after the faceplate is on, never before. Cutting first guarantees misalignment.
  3. Apply a continuous bead of fish-safe 100% silicone around the opening on the skimmer face (or on the back of the faceplate, per your model's instructions). One unbroken bead, no gaps at the corners. Corners are where skimmers leak.
  4. Sandwich the liner between faceplate and skimmer wall, start all screws by hand, then snug them evenly in a crisscross pattern, the way you would torque a wheel. Snug means snug: overtightening squeezes the silicone out of the joint and dimples the liner, creating the leak path you were trying to prevent.
  5. Cut the opening inside the faceplate frame with a sharp utility knife.
  6. Let the silicone cure fully, 24 hours, before water reaches the faceplate. Fill the pond to just below the opening on day one if you must, but the seal does not see water until it has cured. This is the step impatience kills.
Pro tip: Buy one more tube of fish-safe silicone than you think you need, and reject any tube labeled "kitchen and bath" or containing mildewcides. Mildew-resistant silicone leaches biocides into the water. If the label does not say 100% silicone and aquarium- or fish-safe, it does not go in your pond.

Installing the BioFalls: Set It Once, Level Forever

  1. Position it at the head of the waterfall, set back far enough that the spillway lip overhangs your first drop. The excavated spoil from your pond dig usually becomes the berm it sits in; that is the standard sequence in our excavation guide.
  2. Compact the base. Same rule as the skimmer: undisturbed or compacted soil only. A falls filter holds a lot of water; when it settles unevenly, water sheets off one side of the spillway and sneaks behind the liner, which is the classic "my pond loses an inch a day but I cannot find the leak" failure.
  3. Level it side to side exactly. A falls box that is off level by a quarter inch pours visibly off one corner. Front-to-back, follow your model's instructions; some designs call for dead level, some for a very slight forward lean.
  4. Attach the liner to the front face using the included hardware and the same silicone-sandwich-snug technique as the faceplate. On Signature Series units this is the snout and bolt assembly; the corner folds take patience. Pleat the liner into neat folds rather than trimming slack away; you cannot add liner back.
  5. Plumb the bulkhead. Flexible PVC from the skimmer's pump discharge to the bulkhead fitting at the base or rear of the falls box. Hand-tighten bulkhead nuts plus a quarter turn; channel-lock enthusiasm cracks bulkheads.
  6. Load the media: filter mats in the bottom rack, bagged bio media on top, per the box diagram. Rinse lava rock before it goes in or your first week of waterfall is gray.
  7. Rock in the spillway after a test fill, once you have confirmed the sheet of water lands where you want it. Everything you need for the plumbing run is in our plumbing and installation collection.

The Installation Reality Check

What this actually takes

Plan on a half day for the pair as a first-timer: roughly 2 to 4 hours for the skimmer including the faceplate seal, and 1 to 3 hours for the BioFalls including liner attachment and plumbing (typical DIY ranges; we are confirming against professional crew-hour data and will update). Add the 24-hour silicone cure before the pond can fill past the faceplate, which means skimmer sealing is a day-before job, not a fill-day job. The physically hardest part is not the boxes; it is the trench and berm work around them. The precision part is the faceplate height. Measure it three times against your level line, because the cost of getting it wrong is draining the pond and re-digging the shelf.

If you are deciding whether to do this yourself at all, our honest take on crew sizes, timelines, and when to hire out is in Can I Install a Pond Kit Myself?, and the full build sequence these steps slot into is the 10-step kit installation walkthrough.

Get the Matched System, Skip the Guesswork

Every complete kit we carry pairs the skimmer, falls filter, pump, liner, and plumbing so the components are sized to each other. No component-matching math, one warranty path, one box count.

Shop Complete Pond Kits →

Frequently Asked Questions

What does a pond skimmer actually do?

A pond skimmer is a buried box at the pond's edge that does three jobs at once. First, it pulls the surface layer of water into itself continuously, which drags leaves, pollen, grass clippings, and uneaten fish food into a basket or net before that debris can sink, decompose, and feed algae. Second, it houses your pump in a protected, easy-to-reach chamber, so pump maintenance means lifting a lid instead of wading into the pond. Third, it acts as mechanical pre-filtration for the whole system: water is debris-free by the time it reaches the pump and the biological filter, so neither clogs.

The practical payoff is maintenance time. In a pond without a skimmer, surface debris sinks within a day or two and becomes muck you eventually vacuum out. With a skimmer, the same debris sits in a basket you empty in thirty seconds.

How do I seal a skimmer faceplate without leaks?

Four rules cover nearly every faceplate leak. One: dry-fit the liner flat and relaxed against the skimmer wall before any silicone; stretched liner pulls away from the seal over time. Two: run one continuous bead of fish-safe 100% silicone around the opening with no gaps at the corners, which is where leaks start. Three: sandwich the liner between the faceplate and the skimmer wall, start every screw by hand, and snug them evenly in a crisscross pattern without overtightening; crushing the joint squeezes the silicone out and dimples the liner. Four: cut the liner opening only after the faceplate is mounted, and give the silicone a full 24-hour cure before water reaches the seal.

Use only sealant labeled 100% silicone and fish- or aquarium-safe. Kitchen and bath formulas contain mildewcides that leach into pond water.

Do I need a separate filter if my pond kit already includes one?

No, not for a normally stocked ecosystem pond. The skimmer and the BioFalls in your kit are not accessories to a filter; together they are the filter. The skimmer provides mechanical filtration and the BioFalls provides biological filtration, and kits pair them with a pump sized to drive both correctly.

A separate pressurized filter or UV clarifier earns its place in three situations: a heavy koi load near or past stocking guidelines, persistent green water that plant coverage and established biology have not fixed by the second season, or a pond with little to no plant coverage doing the nutrient-uptake work plants normally do. If none of those describe your pond, spend the money on more bio media or better plant coverage instead. For the full inventory of what kits include and omit, see What's Included in a Complete Pond Kit, and What's Not?

What is a biological filter and why does my pond need one?

A biological filter is a home for bacteria, not a strainer. Fish waste and decomposing debris constantly release ammonia, which is toxic to fish even at low concentrations. Beneficial bacteria (Nitrosomonas and Nitrobacter) colonize the filter mats and bio media inside a BioFalls and run the nitrogen cycle: they convert ammonia to nitrite, then nitrite to nitrate, which is far less harmful and gets taken up by plants and algae as fertilizer.

Two practical consequences follow. First, the bacteria colony takes 4 to 6 weeks to establish in a new pond, which is why you cycle the filter before adding fish rather than after. Second, the colony needs continuously moving oxygenated water to stay alive, which is why the pump runs 24 hours a day, every day; a few hours of stopped flow kills the colony and restarts your cycle from zero. Rinse bio media only in a bucket of pond water, never with tap water, because chlorine kills the bacteria you spent six weeks growing.

How high should the BioFalls sit above the pond?

There is no single required height; the falls box needs to sit high enough that its spillway lip overhangs your first waterfall drop, and most installs land the first drop somewhere between 6 and 18 inches above the water for a natural look and pleasant sound. What matters more than height is support and level: the box must sit on undisturbed or compacted soil, dead level side to side, because every inch of height you add also adds head height your pump must overcome. Check your pump's flow curve at the actual lift before deciding to build the falls taller; our pump sizing guide walks through that math.

Can I run my skimmer through winter?

In mild climates, yes, keep it running. In freezing climates most owners shut down the skimmer line for winter: falling debris has stopped, ice can block the faceplate opening, and running water through an exposed falls box builds ice dams that can divert water out of the system. The common cold-climate setup is to pull the pump from the skimmer, run a small recirculating pump or aerator plus a floating de-icer for gas exchange, and restart the skimmer and falls in spring. Full seasonal steps are in the maintenance section of our complete pond building guide.

Not Sure Which Skimmer or Falls Filter Fits Your Build?

Send us your pond dimensions and fish plans. We review the plan, size the skimmer, falls filter, and pump to each other, and tell you plainly if the cheaper option is the right one. No charge, no pressure.

Get Free Expert Sizing Help →
Next article Pond Liner & Underlayment Install: No Wrinkles, Hidden Edges